got mine. updated. installed. what rpm should i be choosing? +500?
got mine. updated. installed. what rpm should i be choosing? +500?
need to update PC software, then update tuner software just as a FYI to everyone
Coolies, just installed the flash.. few notes:
1. Throttle response is better.
2. Restrictor gone is good!
3. From my steady 15psi-ish i was getting before it now peaks and holds around 17psi... ( not sure this is a good thing)
4. Car now back fires in 1st gear from an aggressive launch.
5. Idle was a little bit weird, see how that goes as i put my km's on the car.
Delivered today. Many thanks again to Jmac and Jeff.
I've heard noises along the lines of +250rpm
If all that's changing is the rpm limiter, then I don't see the point for myself, so mine's remaining stock on that front. I don't have it at the top end for long enough to care about 250rpm difference it limiter - I'd rarely see 250 under the limiter.
On the other hand if raising the limiter "stretches" maps in some way - i.e. has an influence other than just a hard limit, then I'm interested. For now I've declined the option.
---------- Post added at 06:48 PM ---------- Previous post was at 06:46 PM ----------
THANKS Justin and Jeff.
Do we need a group install support/feedback/discussion thread?
"Blue Meanie" 2007 Aurora Blue MPS 3 - 18x8.5+44 SSR GTX01 - 235/40R18 Michelin PS5 - 3.5" ETS TMIC - CPE stg 2 mount - HKS/CPE BPV - 2XS inlet - 2XS short shift - Corksport turbo manifold - HT 98 octane tune - Leather/Aluminium handbrake - Momo shifty knob - 7" touchscreen - JDM Mazda Retractable dashtop screen assembly - Bespoke Raspberry Pi Android based GPS/Carplay and instrumentation - 36AH reserve battery and C-TEK isolator - TEIN Street Advanced coilovers 1" drop - Superpro bushings - 220Kw/410Nm.
"Lipstick" 2013 Velocity Red MPS 3 - 18x7.5+48 Enkei RPF1 -225/40R18 Federal RS-RR - CPE TMIC - COBB inlet - CPE stg 2 mount - COBB Stage 1 98 octane tune - COBB shifty knob - 2XS short shift - 2XS turbo manifold.
http://www.ozmpsclub.com/forum/elect...abbed-one.html
thread there about them
posting my initial thoughts there now
"Blue Meanie" 2007 Aurora Blue MPS 3 - 18x8.5+44 SSR GTX01 - 235/40R18 Michelin PS5 - 3.5" ETS TMIC - CPE stg 2 mount - HKS/CPE BPV - 2XS inlet - 2XS short shift - Corksport turbo manifold - HT 98 octane tune - Leather/Aluminium handbrake - Momo shifty knob - 7" touchscreen - JDM Mazda Retractable dashtop screen assembly - Bespoke Raspberry Pi Android based GPS/Carplay and instrumentation - 36AH reserve battery and C-TEK isolator - TEIN Street Advanced coilovers 1" drop - Superpro bushings - 220Kw/410Nm.
"Lipstick" 2013 Velocity Red MPS 3 - 18x7.5+48 Enkei RPF1 -225/40R18 Federal RS-RR - CPE TMIC - COBB inlet - CPE stg 2 mount - COBB Stage 1 98 octane tune - COBB shifty knob - 2XS short shift - 2XS turbo manifold.
Caff Mobile Mk1 - 2010 Aluminum Gen II | 2XS SRI | H&R Lowered Springs | cpe 75 Duro Engine Mount | Whiteline Rear Swaybar | Moog "Problem Solver" Rear Endlinks | 3M Carbon Black Tint | Lakin Custom Plates | Opti-Coat Paint Protection | Paint Correction by Me - SOLD
Caff Mobile Mk2 - 2008 BMW Z4M Coupe - Sapphire Black Metallic | Stock....for now
glad to see that you guys are getting your units in.
Dammit mine's been at the Brisbane Airport depot for 2 days with package status "package not due for delivery". Spoke to FedEx, they're holding it until the guaranteed due date (tomorrow) because it's international economy :P I suppose it's Christmas - they'll be busy.
Might drive out there today if I have time...
I had the same status on my delivery. So I rang them & organised to pick it up.
I bet they'd be more than happy for you to pick it up.....Save them the trip
Anyways, mines installed & running & I love it!!!!!!
The only thing is when I give it a boot full in 1st & 2nd the front wheels start hopping............ so I then have to bak off.
I'm due to install my 65 duro engine mount on Thursday night, will this fix the problem & does anyone else have this issue??????
Just got mine today. Mine also had a break at the depot (not due for delivery) for two days, this time it was at Rydalmere in Sydney. Must be how Fedex works.[COLOR="Silver"]
---------- Post added at 09:17 AM ---------- Previous post was at 09:13 AM ----------
Just got mine today. Mine also had a break at the depot (not due for delivery) for two days, this time it was at Rydalmere in Sydney. Must be how Fedex works.
Last edited by tigamica350; 22-12-2010 at 08:20 AM. Reason: Damn slow internet, double post!!
it's pretty bloody simple really, please excuse the less than perfect video quality
Good work with the video Sam Mine is in Singapore at the moment, should be arriving tomorrow
CES "SS" TBE | SURE "Aeros" SRI | SURE "Sidewinder" TIP | SURE "Return" Recirc Hose | CUSTOM "PWR Core" FMIC | Hypertech "Tuned" | Turbosmart "Atmo" BOV | MSD DashHawk | CP-e REM | SURE "Anchors" Shifter Bushings | JBR SSP and Weight | JBR Heavy Knob |Redline Hood Quick LIFT ELITE | TEIN "SS" Coilovers | Front - Rear HOTCHKIS Swaybars | Front - Rear DBA 4000 Slotted Rotors | A1RM Brake Pads | 18x8 +45 Tenzo-R Cuzco Black V1 | 235/40/18 Michelin Pilot Super Sport | Safe n' Sound baby Seat lol