After some encouragement from Ryan, I converted my exhaust into a twin tip setup.
Fabrication Yoda
Twin tip exhaust
After some encouragement from Ryan, I converted my exhaust into a twin tip setup.
IS NOT A
Look hawt how does it feel?
Forum Regular
I LIKE! That looks really good mate!
Different sound?
I Have The Need For Speed
Hmmmmm I like, I don't want to do to much more to mine until the warranty finishes, but you fellas are making it hard, I only just talked myself out of the dump pipe 2 weeks ago?????Itchy feet again... Thanks guys
Fabrication Yoda
It's only hot when you run the car a 5 minutes. OUCH! Don't touch that againOriginally Posted by LYNCHY
It sounds a little hollow atm because I only had 2.5" piping at home. I will make a new one in 2.25" to reduce the hollowy effect.
, Mine runs out of warranty on the 1st of Nov. Or when the Mazda reps say it's out of warranty.
Achievements
2009 Jamboree Street Compact Winner
Aust. Quickest and Fastest MPS
12.3 seconds @ 111Mph.
Proven over the Qtr mile
Another Mazda 3 MPS - Almost fully bolted - Waiting for a turbo upgrade - The weekend hack.
Toyota Yaris - Coilovers, rollcage, raceseats, harnesses, 18s - Also waiting for a turbo upgrade.
2011 AWD Territory - White and Slightly lowered on 22s - The tow car.
2011 RWD Territory - Black on black and slammed on 22s - The family transporter.
Banned
the RHS tip looks lower then the left
Forum Addict
angle of the shot I think
Black FTW
Gen 2 wana be....
lol
Beeched as Bro'
Looks Excellent mate..
and better than the GEN2
gen 2 est unheheh
Senior Member
looks good
how do they connect to the rest of the system?
Admin Inside
gen2 has covers over the actual zorst like old 6MPS.Gen 2 wana be....
lol
Looks good Troy
Happy Motoring
duglet
Fabrication Yoda
You can see in the bottom picture, it is just a Y piece, cut and welded into the original exhaust.
Achievements
2009 Jamboree Street Compact Winner
Aust. Quickest and Fastest MPS
12.3 seconds @ 111Mph.
Proven over the Qtr mile
Another Mazda 3 MPS - Almost fully bolted - Waiting for a turbo upgrade - The weekend hack.
Toyota Yaris - Coilovers, rollcage, raceseats, harnesses, 18s - Also waiting for a turbo upgrade.
2011 AWD Territory - White and Slightly lowered on 22s - The tow car.
2011 RWD Territory - Black on black and slammed on 22s - The family transporter.
the one
Looks awesome Troy!!!
Decepticon
Dude, that looks fantastic!
I am so going to be putting a dual exhaust on the EVILMPS when the time comes!!
Naturally Awesome
That looks awesome, where did you mount the support for the RHS pipe?
Always had a "hard" spot for twin exhausts
Decepticon
How'd you go with the towing bracket that sits behind the bumper where the extra tip comes out?
Life Member
Looks great mate, good work
Fabrication Yoda
I cut the tie down hook off, and welded a bracket onto the raw edge where the tie down hook was.
I also cut it off today and went back to a single tip. I have a new look I want to try. stay tuned.
Naturally Awesome
Love these new looks and options
Forum Regular
That looks awesome...
I just couldn't bring myself to cut that rear bar! If it's like the MPS6 rear bar, it would set you back like $800 for the black trim alone!
Posting Permissions
Reply With Quote