-
Rayd's Big Power Parts Sale - GTX3071, CPe Ex. Mani, Forged Long Block etc
Item:
GTX3071 ATP Mazda Flanged rear housing - Ceramic coated rear housing to suit EWG
Location: Parramatta area
Item Condition: SOLD
Reason for selling: SOLD
Price and price conditions: SOLD
Extra Info: This awesome turbo was used on my MPS 6 for about 25000kms, no shaft play at all, has been ceramic coated since day one of install, running perfectly when taken out - Never tracked - Comes with custom made Braided Coolant feed line
Pictures: SOLD
Item: CPe Mazda flanged Exhaust Manifold - All Completely ceramic coated
Location: Parramatta area
Item Condition: Great
Reason for selling: SOLD
Price and price conditions: SOLD
Extra Info: SOLD
Pictures: SOLD
Item: Tial 38mm EWG 2 bolt flange
Location: Parramatta area
Item Condition: Good
Reason for selling: SOLD
Price and price conditions: SOLD
Extra Info: SOLD
Pictures:
Item: 4” Full HTP Intake - TIP + MAF housing with air straightener + AEM Dry Flow Air Filter (new)
Location: Parramatta area
Item Condition: SOLD
Reason for selling: SOLD
Price and price conditions: SOLD
Extra Info: SOLD
Pictures: SOLD
Item: ETS 3.25” Top Mount Intercooler - Hot side modded to have 2” entry and built in boost tap, perfect for any Garret turbo but can also fit OEM.
Location: Parramatta
Item Condition: SOLD
Reason for selling: SOLD
Price and price conditions: SOLD
Extra Info: SOLD
Pictures: SOLD
Item: Stratified Boost Dial
Location: Parramatta area
Item Condition: SOLD
Reason for selling: No longer required
Price and price conditions: SOLD
Extra Info: SOLD
Pictures: SOLD
Item: Perrin 3 port EBCS
Location: Parramatta area
Item Condition: SOLD
Reason for selling: SOLD
Price and price conditions: SOLD
Extra Info: SOLDPictures: SOLD
Item: Denso ITV22 iridium 1 step colder spark plugs
Location: Parramatta area
Item Condition: NEW
Reason for selling: Ordered or customers who didn’t pay
Price and price conditions: $85 per set shipping included
Extra Info: When boost gets turned up in these motors so does combustion temperatures, this means that the OEM spark plugs are operating out of there efficiency range and may promote engine detonation or pre-ignition and hence will cause a higher amount of Knock Retard on your MPS, especially when driven hard.
Hence you move to one step colder plugs which can more effectively battle these higher combustion temps by staying ‘colder’ and help battle KR!
Pictures:
Item: Slot reserved for Spec stage 3+ Clutch
Location: Parramatta area
Item Condition: Used - 45000kms
Reason for selling: Need more torque clamp capacity
Price and price conditions: $TBA - To be swapped out and available in a couple months
Extra Info: This clutch is one of the best clutches for balanced performance and drivability, great pedal feel maybe 25% harder than OEM pedal feel but still maintains a massive 650Nm torque capacity.
I’ve taken good care of this clutch, Has never slipped, Maybe launched 3-4 times in its life time, never tracked, never abused.
Pictures:
Soon to be uploaded
Item: Slot reserved for Fidanza lightweight Billet Aluminium Flywheel
Location: Parramatta area
Item Condition: Great
Reason for selling: Does not mate up to my heavy duty clutch kit
Price and price conditions: $TBA - To be swapped out and available in a couple months
Extra Info: This flywheel is much lighter than the OEM dual mass, 11lbs vs 22lbs. Removing this much UNSPRUNG mass means that your engine will rev faster, your turbo will spool quicker, your car will accelerate faster. It even has a removable friction plate which i will be replacing with a brand new plate once i pull it out.
Pictures:
Soon to be uploaded
Item: Slot reserved for Forged MZR DISI 2.3L long block
Location: Parramatta area
Item Condition: 45000kms
Reason for selling: Built New High Compression and custom spec long block
Price and price conditions: $TBA - To be swapped and available in couple months
Extra Info:
Specs on the long block are as follows:
Forged K1 Rods
Forged 88mm Wiesco 9.5:1 Compression ratio 22.5mm wrist pin Pistons
Clevite Main Bearings
Clevite Rod Bearings
ARP Crank Bolt
ARP Main Studs
ARP Head Studs
Runs great - Compression tested recently @ 170psi across all cylinders
Been a solid engine since it was built
Very happily handle big power has been living around the 300kw/550Nm mark for most its life - Street driven, never tracked
Will come as an assembled Long block - just need to bolt up your accessories like intake/ exhaust manifolds, HPFP, fuel rail and pulleys and you’re good to go
Engine is fully swappable into any Mazda 3 MPS, 6 MPS, or CX7 if you’re that way inclined !
Pictures:
Soon to be uploaded
Happy for pickup or shipping within Australia is also available
thanks for looking!
~Ray
Last edited by Rayd; 05-09-2014 at 07:01 PM.
-
Item: Pedders Super Low Springs for Mazda 6 MPS / Mazda 6 N/A
Location: Parramatta area
Item Condition: Great
Reason for selling: Moved to Coilovers
Price and price conditions: $250
Extra Info: Lowering Springs will drop the 6 MPS to potentially the most practical and nicest height you can achieve with a set of lowering springs.
Pictures:
Post reserved for future items
Last edited by Rayd; 03-09-2014 at 09:30 PM.
-
-
PM sent
-
interested in fidanza fly wheel
-
-
-
-
Cheers Rayd, received PM. All good.
-
OP updated - Marked items that are sold
CPe exhaust manifold - Tial EWG and Spark plugs still available.
-
let me know when you are ready to part the flywheel and how much and we can go from there @Rayd
-
bump
-
Interested in cost for long block...EOI
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules