Search:

ET48 and there is loads of clearance both inside and outside with my current 235's, 245's would still cause no problems with clearance but it looks like they would with the AWD system.

Thanks for the input but it is running non OE 8.5J x 18 wheels so 245 would not be an issue as far as rim width is concerned.

Since getting my rear arches rolled and fractionally pulled I reckon I can now easily get 245 x 40 tyres (on the rear only) to replace the 235 x 40 that I am currently running.

My question is...

I apologise (link now removed), but seeing as I am in the UK I tend not to look at the vendors/sponsors sections that much, for obvious reasons.
However, in your opinion ( seeing as Silver is...

I am not sure if you can get it over there, It is called FinishKare.
Of ALL the carnuba paste waxes I have used over the years it is by far the best.

Sounds to me that when you clayed the car you removed ALL the previous wax and protection that it gave, but that is what a clay bar is for, it removes every last trace of surface contamination, be it...

So in a nutshell ?? it is worth fitting all 4 sets of bushes.
Mine is already lowered so that part of the job is out of the way.
I will aslo be fitting a Whiteline rear bar at the same time as the...

Well between us we can get somewhere near perfect, I am in the UK but those yank figures look pretty good as a starting point.

A huge thanks to both Toddy and Rogwick for the info contained within their PM's.
I really do prefer Toddy's because to me it looks slightly more aggresive being that much lower but I think I might...

Ok, I sent them an email and although they are willing to do a 3 gauge pod in RHD form for the MPS6 they need and initial order of 40 units, it would seem that is the end of that lead:sosad:

Hi Toddy,

Well, my parents are in Ballajura WA so a small trip to the retail outlet would make a nice little day out for them.
Is it possible you could PM the exact details.

Cheers

Have I missed something here ??

The OP asked that if he went up from 8 to 8.5 rims with the ET staying the same, with the 235/40/18 rubber also staying the same would the tyre get any closer to...

I have sent them an e-mail and await their reply.
You don't have to use screws, that is the "free/no charge option" you can also choose the "silicon/clamps" option although I would use windscreen...

Personally I prefer Toddy's version:2thumb:, Where do both types come from ? I might get my Mum and Dad to get me some in Oz and send it over to me in the UK, I have looked averywhere in the UK and...

That would be great, thanks.

I have already lowered the car but have yet to get the geometry reset, I am not using the car at the moment so no harm done.
I thought I would do all these bushes +...

Thanks for the link, while I am at it (will have most of the front suspension apart anyway) I thought I would also order and fit the Control arm lower inner and outer bushes (SPF2954K, SPF2955K). I...

Hi guys and sorry for feeling the need to resurrect this thread, BUT, I do have good reasons:2thumb:

I have read this thread 2 or 3 times over and am still at a loss as to what parts to order for...

Welcome along, if the oher guys could start their cruise by heading to the UK to pick me up it would be much appreciated:2thumb:

I haven't yet, will send them an e-mail now.

Thanks

Thanks for the warm welcome guys, now see if any of you can help me with my question posted in general
http://www.ozmpsclub.com/forum/general-mps-mazdaspeed-discussion/6013-need-help.html#post107552...

Hi Guys,

I need your help.

I have searched most of the USA sites for a dash top gauge pod (one that replaces the pop up lid) but they all seem to be for LHD cars only.

As you are RHD (IMO...

Enfield, about 2 miles from J25, that is the right at the top of the "road to hell" if you were looking at it on a map.

Just thought I would pop by and introduce myself.
Only had the MPS6 for a couple of months although nearly one of those was spent in Oz staying with my parents in Perth WA, my brother and his family...