It's a genuine mazda part :) Yeah im really funny when it comes to putting aftermarket things inside the car where possible,i like to keep it looking stock clean but better if that make sense :)
Type: Posts; User: Supereunos
It's a genuine mazda part :) Yeah im really funny when it comes to putting aftermarket things inside the car where possible,i like to keep it looking stock clean but better if that make sense :)
Hey yeah i wasnt keen on the rx8 one mainly cause the H pattern was different the R is where our 6 is. it's a genuine part go to this link
Illuminating Gearknob, Leather Brushed Alloy, 6 Speed,...
to be exact mazdas workshop manual tells you bolt A which is the smaller end of the mount to tighten 85.3nm - 116.6nm (62.93ft lbf -85.92 ft lbf)
and bolt B the larger end of the mount that...
Mazda workshop manual states the oem one should be torqued to 116.6nm for front and rear bolts on the dog bone mount. which is alot more than the 65 odd nm that Sure says to torque their mount :S
[QUOTE=Jmac;235013]I doubt the AP will solve your problem. I believe (though could be wrong) the WOT hesitation fix is for non stock cars.
Is your exhaust turbo back or cat back?
It could...
It's all Stock except a exhaust. i couldn't hurt to put new plugs in as for boost leak in theroy wouldn't that show on my gauge the drop in pressure?
When you you say wot wat iv started experiencing is if i give it stick up to say 110 it has what seems like a miss round 5g rpm and sometimes even down low as it comes on boost will hesitate and...
I notice mine more so on down shift round 3 and 2 i find i have to hold the clutch just right upon releasing other wise i get a thump it's annoying i thought it was the factory clutch but upon...
Old thread i know but my 07 mps 6 seems to have a slight misfire that has just occurred noticeable in the higher rpm range and sometime round 3000 odd, it used the have what appeared to be little...
When you speak of exhaust mods i bought my 07 mps 6 with a 3" middle section installed from the previous owner, now upon emailing a talking to mrt performance about best way to get the some more...
You may be right i told them to check mounts etc and they recon they did, the exhaust place told me the system had shifted cause the muffler was hitting against the back of the car so they had to cut...
Well Car is back at dealership cause i got back and the car was jumping out of gear and not engaging reverse properly apparently now is has a stuffed shift cable hence why it was only doing it on...
Thanks jetmps just got it back yesterday, now much nicer to driver the gearbox feels tighter now :), they forgot to put the under engine tray back on so i had to go, and get that done. Plus it was...
i have had this Thumping like noise when i release the clutch well, the dealership was certain it was inside the box on my 07 mps 6, cracked the box open had a look, put it back together went for a...
I asked that question and they said all the mounts are fine, Kinda disturbing that fact the car only has 64,000 on it but i guess no matter what car you buy, they all have problems so worse than...
My 07 Mps 6 is making a wicked thumping noise which i notice more of down shift it's annoying, the dealership has told me they recon it's a internal problem in the gearbox and are pulling the box out...
It's not a autoexe box i just bought one from a japan import if you look close you can see the difference in the shape etc10568
When you can get it cheap it makes it worth while :)
The diameter of the maf housing is about 63mm roughly. I only want the best for her, i even imported autoexe brake pads from the states, as many would know autoexe staff are ex mazdaspeed staff, so...
10566This just arrived from an import from nz, come off a mazda atenza and is to be fitted to to a mps 6 with sure intake pipe kit, as it did not come with any pipes and no doubt come off a na...
I remember seeing that not long ago on car sales, 2 dead give aways that it's either a jdm import or not (anyone can slap a mazdaspeed atenza badge on) is if it's a jdm variant it will have rear...
Interesting that means my baby only has 1508 siblings in Aus not many in reality which makes it good cause it makes our cars more unique. And if i can justify spending the massive dollars mine will...
You could tour the world helping people install their gauges :P
Dont touch the one in plastic pipe i tried that and upon pulling hose off it snapped off. cost me just under 200 dollars for a new one from mazda. Go to autobarn or somewhere and do what i did get a...