Search:

Type: Posts; User: TylerAtCorkSport

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    11
    Views
    3,408

    Could always get a battery load test to see if...

    Could always get a battery load test to see if your battery is starting to fail, clean the terminals while you're there! Also test your starter if you have time.
  2. Replies
    16
    Views
    5,899

    With the turbo charged motor option, I have a...

    With the turbo charged motor option, I have a feeling that would be a great selling RWD sports car. I'd figure out how to buy one. lol.
  3. Replies
    16
    Views
    4,346

    I re-bed my brakes on each of my cars every 6...

    I re-bed my brakes on each of my cars every 6 months or so. Usually right before I do my spring details and my winter preps... Also, bed the brakes the same way on my Harley at the beginning of...
  4. Replies
    16
    Views
    4,346

    Here's a great way to bed in brakes. It should...

    Here's a great way to bed in brakes. It should take away some of the noise, if not all of it.
    How to Bed-in Brake Pads and Rotors - YouTube
  5. Replies
    1
    Views
    1,318

    It looks like like a quality piece. One of my...

    It looks like like a quality piece. One of my best friends had a CRX. Fun little cars.
  6. Replies
    27
    Views
    8,861

    Let us know if that fixes it. That makes sense...

    Let us know if that fixes it. That makes sense if you're braking hard enough to activate the ABS system. I'd like to hear the outcome to this!
  7. Replies
    10
    Views
    2,708

    I had to laugh at that. :) PO. Why do you...

    I had to laugh at that. :)

    PO. Why do you need the 350-370 bhp numbers? Is that what you think you need to compare to something else?
    IF it were me, I'd start with a FMIC w/ Ramair, fuel pump...
  8. Replies
    6
    Views
    1,584

    1.) I would get your car checked out by an...

    1.) I would get your car checked out by an independant mechanic or the dealer for quotes on noise issue. Hopefully it's nothing major!
    2.) Again, it depends on how the clutch has been treated, many...
  9. Replies
    13
    Views
    2,876

    I agree with the rattle due to the exhaust since...

    I agree with the rattle due to the exhaust since you're saying that it's only at certain RPM's. The way to get rid of that would be to add a resonator to the exhaust... or add the two rubber...
  10. Sticky: This looks to be the start of a great thread!

    This looks to be the start of a great thread!
  11. Timmy, Let me know when you're ready to order....

    Timmy,

    Let me know when you're ready to order. :)

    -Tyler
  12. One thing to consider is that our down pipe is a...

    One thing to consider is that our down pipe is a divorced style as opposed to the bell mouth. We found better testing with the divorced style, and stuck with that design over the bell mouth opening....
  13. PM Sent :)

    PM Sent :)
  14. Replies
    7
    Views
    2,405

    Where would your clutch go? Just kidding. ...

    Where would your clutch go? Just kidding.

    I would read your codes and see if there is a code that's not triggering a CEL. Normally, if you have a bad clutch, it would act like revving in...
  15. One thing that I usually suggest when going with...

    One thing that I usually suggest when going with a larger diameter exhaust such as our Power Series is getting upgraded Urethane Exhaust hangers. The stock rubber hangers can allow for the exhaust...
  16. Sticky: I would imagine you would be fine w/ your setup. ...

    I would imagine you would be fine w/ your setup. Usually we'll see safe fuel pressure up until you open the downpipe. Unless you're running a turbo back exhaust and are doing high gear pulls under...
  17. Replies
    29
    Views
    6,221

    [NSW] I like the hood. Looks good.

    I like the hood. Looks good.
  18. Replies
    8
    Views
    1,613

    [NSW] Jacid, I don't think the non-posting of pictures...

    Jacid, I don't think the non-posting of pictures works... You need to post them up so us addicts can get our fix :) Welcome to the boards!
  19. Replies
    15
    Views
    2,780

    [NSW] Welcome to the forum, got some pictures? :) To...

    Welcome to the forum, got some pictures? :) To upload just click on the little icon that kinda looks like a tree, browse for the photo and there ya go!
  20. This job in my opinion is a pain with a hoist... ...

    This job in my opinion is a pain with a hoist... let alone jackstands. Don't get me wrong, completely do able, but not a fun job either way. Good luck, take your time, practice patience, and my...
  21. Replies
    16
    Views
    5,221

    Smokey is correct, the gen 1's and 2's don't need...

    Smokey is correct, the gen 1's and 2's don't need the air straightener unless you want it in cold climates and custom tuning. You'll be fine without the Air Straightener on the CS Stage 2 SRI
  22. Brad, We've had great feedback on our camber...

    Brad,

    We've had great feedback on our camber arms. Everyone seems to love it, the only negative so far as been the install. The camber arms can be a pain due to the fuel filler location :(.
    ...
  23. Replies
    79
    Views
    21,396

    naasif, I'm taking your suggestions to our...

    naasif,

    I'm taking your suggestions to our Engineer! :)

    -Tyler
  24. Replies
    79
    Views
    21,396

    Naasf, we're very pleased that you're happy. I...

    Naasf, we're very pleased that you're happy. I can't wait to see how you like it! :)
    -Tyler
  25. Replies
    8
    Views
    2,041

    Dang, that looks good! How was the application? ...

    Dang, that looks good! How was the application? I've been thinking of getting some, but it's not very cheap!
    -Tyler
Results 1 to 25 of 84
Page 1 of 4 1 2 3 4