The wire was fine, it extends all the way to the solder.
Have had the car back for 3 days from Mazda and it seems fixed (don't want to jinx it!). Dirty and blocked injectors appears to be the...
Type: Posts; User: CHMPS
The wire was fine, it extends all the way to the solder.
Have had the car back for 3 days from Mazda and it seems fixed (don't want to jinx it!). Dirty and blocked injectors appears to be the...
http://images.tapatalk-cdn.com/15/08/26/05342d0ba9e35a811fa4134ecc670f3d.jpg
Anyone think this could be the issue? Condition of ground wire for coils looks a little dodgy at the crimp
Sent...
Hi Guys,
Anyone make anything of this dyno run and recommendations? Seems like alot of those checks could have easily been done via accessport. Dyno run is the crappy looking one with 14 AFRs....
12v like cigarette lighter one? That's what I've been trying, have been including the intake side though which is not ideal probably. Need to make the effort to take off the tip and pressure test the...
Cheers, for the advice, yes I wouldn't even usually go wot, guess just a combination of frustration and trying to get data!
Ps does anyone have any luck just using a bike pump or cigarette lighter...
Cheers adz, any way to check the connectors with a multimeter/test light?
So far I have
Changed plugs
Changed 2 coil packs in each locations.
Cleaned maf sensor
Cleaned map sensor.
Could do...
You reckon? Photos are different lights. No luck with the new coils in the other locations. Have new ones in now, Mazda said they were ok but not sure I can trust that! 2 Logs, with two brand new...
Don't have any codes! It is a stutter /hesitation throughout the rev range. No luck with the 2 new coils in cylinders 1 and 2. Will have a look at the map, cheers
Sent from my iPhone using...
Am replacing 2 coils tomorrow, which is the most likely to be bad? Try the other two if that doesn't work. Bought a grounding kit for good measure.
The map is in the intake manifold? Big job?
...
Yea cleaned the maf sensor when I regapped the plugs, wasn't really dirty anyway. Am thinking I possibly have a cracked plug insulator as I didn't really check that. Just need a chance to put new...
Still no luck, have got the new o-ring. Gapped plugs at .026". Have been told to check my grounds, is this visual or with multimeter, how do I do this?
Sent from my iPhone using Tapatalk
https://trademe.co.nz/864542229
White!
Sent from my iPhone using Tapatalk
More power on the gen 1 without it! Any ideas for a substitute maf o-ring? Am waiting on one from mazda
Hey mate, have actually taken the air straightener out as corksport said it's not needed on the Gen 1. Yea i might put it all back together with the regapped plugs and see how it runs.
I'm interpreting them as light grey = normal, but I am colourblind haha,
Sent from my iPhone using Tapatalk
Pulled the plugs, all seem pretty normal to me, one seemed to be gapped far too small so another possibility! Wondering if I should just put a brand new set I have sitting here in?
...
Just cleaned the maf sensor, found that the o-ring is buggered so that's a possibility, will have to order a new one ASAP. Clamped it down good and took this maf cal - no change still running badly....
Hi Guys,
Cold start was really rough for me today and didn't get much better with the car running like a dog, misfiring I think through gears and rev range. Is quite cold here at the moment, (5-9...
Going raydtuned, 2 revisions in!
Have had this on for about a week now. To me there are no noticeable vibes, the shifting actually feels smoother than the jbr 70 mount. As for performance, I would say I didn't notice a huge...
Ok cheers for that, yea considering both rayd and stratified
Sent from my iPad using Tapatalk
Hi all,
Have finally managed to install my autotech fuel pump internals this week, so now my mods are: corksport stage 2 Sri with tip, de-cat mod (thanks to 2xs), street unit tmic, turbosmart...
Have bought the mount, so will let you all know compared to my JBR 70 duro when it arrives and once I can find the bolt!
If anyone knows/can find out the part number for the through bolt it'd be much appreciated! I know the mount itself is CM5Z-6068-A, but can't find the associated part numbers for the bolt anywhere.
Ok cheers, yea thats what I was thinking. Through bolt or bushing bolt?