Search:

Type: Posts; User: Rayd

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    15
    Views
    6,066

    Pressure plate needs to get balanced too Shane

    Pressure plate needs to get balanced too Shane
  2. Replies
    21
    Views
    8,101

    Mine needed a bit more than a few mm off the stud...

    Mine needed a bit more than a few mm off the stud to fit my balance shaft unfortunately.
    Ended up having to notch out the casting of the balance shaft to clear the studs. But it fits now :)
    ...
  3. Thread: My Engine Build

    by Rayd
    Replies
    97
    Views
    34,670

    Buy an AP or VT hire a dyno for a couple hours ....

    Buy an AP or VT hire a dyno for a couple hours .
    Sorted
  4. Thread: My Engine Build

    by Rayd
    Replies
    97
    Views
    34,670

    To be fair - when i did the BSD I had 80Duro rear...

    To be fair - when i did the BSD I had 80Duro rear mounts and 80Duro side mounts, i didn't try put the OEM mount back in for comparison. Plus the idle vibes weren't that bad (although definitely bad...
  5. Thread: My Engine Build

    by Rayd
    Replies
    97
    Views
    34,670

    Great stuff rob :) Looking forward to hearing...

    Great stuff rob :)

    Looking forward to hearing your impressions of the BSD
  6. Thread: My Engine Build

    by Rayd
    Replies
    97
    Views
    34,670

    Pretty lucky on the main studs, mine needed about...

    Pretty lucky on the main studs, mine needed about 3-4mm taken off and needed to use a thinner washer to clear the balance shaft - did you have to take anything from the nut for it to clear?
  7. Replies
    251
    Views
    84,985

    Yep :)

    Yep :)
  8. Replies
    251
    Views
    84,985

    Our engines lift heads all the time with big...

    Our engines lift heads all the time with big power and constant abuse thats why i use L19's for head studs - but luckily the main studs hold the crank girdle on and the ARP's are plenty enough for...
  9. Replies
    251
    Views
    84,985

    I know , thats why i'm gonna try this first then...

    I know , thats why i'm gonna try this first then if it doesn't work, i'll look into alternative options.
  10. Replies
    251
    Views
    84,985

    I was thinking of using 6/8 ARP's then 2 OEM's in...

    I was thinking of using 6/8 ARP's then 2 OEM's in that particular place. Will see how i go with this route first.
  11. Replies
    251
    Views
    84,985

    My ARP's had no chance to clear the balance shaft...

    My ARP's had no chance to clear the balance shaft - had to cut 3mm off , tap the thread down further so it can get to the bottom of the block and use a thinner washer on the top so the balance shaft...
  12. This getting way out of hand No idea what...

    This getting way out of hand


    No idea what your problem with me is Sam, i have never spoken to you outside of this forum nor worked on your car, don't you have anything else better to do than to...
  13. Replies
    6
    Views
    1,706

    [NSW] Welcome mate; keep an eye on that Luke character;...

    Welcome mate; keep an eye on that Luke character; he lives up there too and seems to sniff out the MPS owners around town
  14. Thread: My Engine Build

    by Rayd
    Replies
    97
    Views
    34,670

    Passing comments combined with personal research...

    Passing comments combined with personal research mostly ;)
  15. Thread: My Engine Build

    by Rayd
    Replies
    97
    Views
    34,670

    Firs they weigh the rods and pistons and ensure...

    Firs they weigh the rods and pistons and ensure they are all the same weight and even weight distribution top - bottom - left - right.
    then they spin each rotational part individually to make sure...
  16. Replies
    4
    Views
    3,756

    Meth injection throttle body spacers

    Yeah it's a good idea, but keep in mind that the spacer is post-trottle body and will require a solenoid for correct operation of the nozzle.
    I've tried check valves with up to 16psi cracking...
  17. Replies
    10
    Views
    6,848

    Chinese eBay 8" model There's a few sellers...

    Chinese eBay 8" model
    There's a few sellers advertising it atm
  18. Replies
    10
    Views
    6,848

    I have been waiting for the android model for the...

    I have been waiting for the android model for the last 12 months!
    Couldn't wait any longer and got this one:
    Works very very well highly recommended!
    ...
  19. Thread: My Engine Build

    by Rayd
    Replies
    97
    Views
    34,670

    correct - the only truly balanced 4cyl is the...

    correct - the only truly balanced 4cyl is the boxer engine.

    also - my engine did have individual rotational balancing and the balance shaft can't be attached when balancing the crank.
    I have...
  20. Replies
    251
    Views
    84,985

    I'm about to order some engine internals for some...

    I'm about to order some engine internals for some other members from SP63, if your keen I can chuck your stuff in the order aswell .
  21. Replies
    161
    Views
    49,224

    :( looks like rings or lands are no good - is...

    :( looks like rings or lands are no good - is your coolant discoloured or levels dropping? may be head gasket failure or head lift around 2-3-4 aswell?
  22. Replies
    161
    Views
    49,224

    Shame to hear Reedy :( What were the results...

    Shame to hear Reedy :(

    What were the results of the compression test? and did they do both dry and wet? also where did the leakdown point to the fault to be? intake/exhaust valves or rings?
    I...
  23. Replies
    11
    Views
    2,747

    bozjet can sort you out I'm sure

    bozjet can sort you out I'm sure
  24. Replies
    2
    Views
    1,737

    your ECU will always run the timing map which...

    your ECU will always run the timing map which contains the lowest values, you're probly running a different map in the "knocking" table i imagine.

    make all your timing maps identical and it will...
  25. Replies
    28
    Views
    12,371

    the 6 barely has any torque and boost...

    the 6 barely has any torque and boost restrictions in 1st and 2nd, something like 1.58 load in 1st/2nd vs 1.68 load in 3rd-6th which is really not much when compared to the 3's, so likely wont make...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4