Search:

Type: Posts; User: Paul G

Search: Search took 0.03 seconds.

  1. Replies
    7
    Views
    4,513

    Try changing your engine oil for a different...

    Try changing your engine oil for a different brand. I was using Castrol Edge 5w30 full synthetic which is one of the cheapest synthetics around in 2 new cars and never had to add any oil. When I...
  2. Newer is usually better and mazda MPS engines are...

    Newer is usually better and mazda MPS engines are better engines than SR and RB serious. However FWD will never feel as wild in the first gear as AWD. Engine is not only about power like SR and RB...
  3. Replies
    2
    Views
    1,312

    I'm not 100% sure but with the BNR stage 1 you...

    I'm not 100% sure but with the BNR stage 1 you probably don't need the tune running the factory computer, but with BNR stage 3 definitely you need a tune. Now the fuel pump- that depends on the...
  4. When you start modifying your car and you put...

    When you start modifying your car and you put much better parts than original factory you will be doing that because the car will be "pushed" and that's what kills it. You can have the best car with...
  5. Hi. Cobb AP is very good. If your car is...

    Hi. Cobb AP is very good. If your car is standard, that is the first and best mod for it. All other things like cai, dump pipes, fuel pumps will give you more power but will also put more stress on...
  6. Replies
    33
    Views
    8,632

    I only got up this morning because I'm going to...

    I only got up this morning because I'm going to Philip Island to watch car racing. I will be home later tonight.
  7. Replies
    33
    Views
    8,632

    http://www.ozmpsclub.com/forum/ecu-modification-fl...

    http://www.ozmpsclub.com/forum/ecu-modification-flashing/14578-cobb-ap-tuning-melbourne-3.html
  8. Replies
    33
    Views
    8,632

    Yes I have posted a review including dyno graph....

    Yes I have posted a review including dyno graph. However since than I have increased target boost settings by 1-1.5 psi between 3000-6000rpm, so the graph is out of date. The reason why I increased...
  9. Thread: Springs

    by Paul G
    Replies
    42
    Views
    12,146

    I have not seen any springs to suit Gen1 MPS to...

    I have not seen any springs to suit Gen1 MPS to be perfect- belive me I looked for it for long time. In my opinion only custom made set will work. If you lower your MPS by 10-15mm it will be ok if...
  10. Thread: Springs

    by Paul G
    Replies
    42
    Views
    12,146

    Not all coil over are hard and uncomfortable....

    Not all coil over are hard and uncomfortable. Also they have adjustments that help. However you want something like compression and rebound adjustment. Just rebound is not enough. Also all King...
  11. Replies
    33
    Views
    8,632

    If you after performance get it custom tuned....

    If you after performance get it custom tuned. Maps off the shelf are not the best. They only run 2 degrees more advance timing and boost setting is crazy in the mid range rpm so you get wheel spin,...
  12. Replies
    28
    Views
    13,684

    My dyno print out 2008 Mazda 3 MPS (hoping this...

    My dyno print out 2008 Mazda 3 MPS (hoping this will work)12917. This is tuned at 16psi. I was getting similar top end power on Stage 1 98 octane (ver 231) on 19 psi when my car was not custom...
  13. Replies
    28
    Views
    13,684

    Hi. I drive Gen1 2008 3MPS and Tim from RX8...

    Hi. I drive Gen1 2008 3MPS and Tim from RX8 Specialties has tuned Access Port in it on the dyno. The result was 175 kw atw at around 16psi . Also pick power is excellent and pretty flat between...
  14. It also depends on the CAI itself as some give...

    It also depends on the CAI itself as some give better results than other. I can tell you I have the same car 2008 3MPS and CS turbo inlet pipe works well, also removing air snorkel from the front of...
  15. Replies
    35
    Views
    21,042

    Hi. I have a 2008 Mazda 3 MPS with a standard ...

    Hi. I have a 2008 Mazda 3 MPS with a standard computer. When Shell used to sell that V Power Racing 100 octane I ran the car on it all the time and there was a very noticeable improvement in power,...
  16. Replies
    5
    Views
    1,725

    Hi. I have a 2008 Mps and stock cooler. I'm using...

    Hi. I have a 2008 Mps and stock cooler. I'm using Iphone with REV2 app. My intake temperature is usually about 3-4 deg C higher than ambient when I cruise on freeway and up to 25 deg C outside. But...
Results 1 to 16 of 21