15872 This is the seal I'm talking about Green is the seal thats leaking apparently I can not get this and have to buy the whole shaft as one part?
Type: Posts; User: JestaT
15872 This is the seal I'm talking about Green is the seal thats leaking apparently I can not get this and have to buy the whole shaft as one part?
15872 This is the seal I'm talking about
I was quoted 2700 for the whole shaft from mazda my rear boot is leaking grease but they wont sell the seal separate I need a better solution can anyone help with advice ?
Direct Clutch Services in Albion
Andy the dule mass flywheel cuts down on engine vibration that feeds back into the transmission ie makes your ride quiet the down side is it can not be machined so when it wears down it needs to be...
Hey guys you were right it is the VVT is it a factory fault or something??? anyone know if it will cause damage and where in Brisbane is a good place that has worked on the MPS 6 before??
Hey guys,
I have a rattle at start up that sounds like it's getting worse. I believe that the timing chain has come loose at 74,000k anyone else had this problem?? and does anyone know a good...
Hey Guys,
I've been thinking about cutting out the plastic around the bottom left fog light and replacing it with some form of mest to allow more cold air straight to the pod filter which sould be...
Get the Evo 10 has my vote better then a rex quicker then an rx8 and 350z is a bit gay when compaired to the EVO mmmmmmmmmmmmmmmmmmmm..........
very interesting and I apreciate the info you have posted great stuff.. it's interesting to see how this system works as it's different to everything else ive seen so far.
Cheers
Hey Tigamica350,
Welcome to the site . . . Enjoy!
OK Here it is what do you think!http://i365.photobucket.com/albums/oo99/JestaJones/18012009291.jpg
------------------------------ Double post merged ------------------------------...
Hey mate,
I was told there are only one set of 19" that would fit (THAT they could find anyway) and they sucked, I'm sure you could find a set some were though, the off set was too low and they...
yer the coil overs are out of my price range atm and im getting a good deal on the kings i'll prob just go with them for now. . . . should drop it about 1inch alll round without loosing too much ride...
yer i like the style which is what drew me to the vizzo's I think these will look just as good and with 18x7.5 I dont think i'll have any rubbing problems Yey! so back to the shop tomorro to have...
ok the vizzo dont fit so i think im going for these http://i365.photobucket.com/albums/oo99/JestaJones/1307200745846846_m.jpg
http://i365.photobucket.com/albums/oo99/JestaJones/1307200745846846_m.jpg
These are the Gmax enigma that im considering now insted 18"x7.5" with the right off set this time I hope! I think they...
Thanks Shin,
They will be running on 235's ona 36 profile so it's almost the same dimater as the original size only out by a couple of mil so I'll find out tonight as I'm going to pick them up...
Thanks man,
I went and saw them to day it's actually 19" x 8.5" with a 45+ offset I think they are going to use 36 tyres insted of 40 so 36 will give me a really low profile tyre to make em fit...
This may be a dumb question
Does any one know what the stock psi on the turbo is?? and how much I can tune it up without stressing the motor ?
Good point I was having a look at this last night I'm not sure if i have the measurements right correnct me if im wrong but if the standard rims are at 55 it must be negative ? because the rim is...
IMG]http://i365.photobucket.com/albums/oo99/JestaJones/Picture003.jpg[/IMG]
These are going on next week 19"x8.5" I think the offset is +42
------------------------------ Double post merged...
sweet thanks guys i'll msg mps garage about getting one sent up
the 6 comes with a 55 off-set i was told I could go 40 without a roll and maybe 36 with some roll work?
where did you get a pre filter???