XEDE Two Map plus Switch possibility

Hey,
I have a XEDE installed and was thinking about their two tuning map ability. I drive alot of ks so I dont want it heavily boosting in city driving, but also want to have the the extra power when I pull up at the lights beside one of you :whistle:

So what I was thinking is having it tuned with a high and low map and then running a switch/button around to where the light dimmer/DSC buttons are on the right hand side near the key there...

Anyone got a XEDE isntalled and running two maps, and how do you have it set up?
Is there anything impossible or crazy about my idea?
Any other suggestions?

Cheers.

Definately doable I think.

Rino who is got a Haltech interceptor, got installed a switch where he can go from 14psi to 18psi anytime he feels young again :D :p

Did you get Allstar to do that Rino? Cause that is who I will be asking if I am going to go ahead with it..

Yep he is tight with the boys at Allstar.

Hehe, I didnt notice :-p
I hope to be too from now on, since the warranty has mostly be voided on the car with Mazda I dont really have much use for them. So I'll get the Allstar guys to do all my services etc.

i have the swich under my stering whell.. but sadly since sold the xede!
stock boost and 20.1lbs were my options!

Quote:

---

Originally Posted by ZedN

Did you get Allstar to do that Rino? Cause that is who I will be asking if I am going to go ahead with it..

---

They certainly did Zed :whistle::whistle::p

I have NASAs XEDE and I'll be having the 2 tune setup very soon.

Quote:

---

Originally Posted by 2XS

I have NASAs XEDE and I'll be having the 2 tune setup very soon.

---

:2thumb: Haven't had to play with mine yet, running good on 14.5.....

Well that is brill then cant wait. Putting the switch in might be costly though

Quote:

---

Originally Posted by ZedN

Well that is brill then cant wait. Putting the switch in might be costly though

---

:nono::nono::nono: not at Allstar :2thumb:

Quote:

---

Originally Posted by ZedN

Well that is brill then cant wait. Putting the switch in might be costly though

---

my turbo seals went.. but its a fail on mazda so they will replace it turbo regardless!!
but what they dont know wont hert them

Quote:

---

Originally Posted by Mr Nasa

my turbo seals went.. but its a fail on mazda so they will replace it turbo regardless!!
but what they dont know wont hert them

---

Ive got no issues there since I am getting mine replaced at the moment with a garrett so I should have alot of life in it :-) I might get it back tomorrow it is taking soooo long, 3 weeks this Thursday. And no, it wasn't covered underwarranty.

Quote:

---

Originally Posted by ZedN

Well that is brill then cant wait. Putting the switch in might be costly though

---

You can purchase the dual map switch kit from ChipTorque for $25. Or any SPST switch will work.

For XEDE's located in the engine bay, you could be looking at $120 to $180 to wire in and mount the switch, depending on how tricky it is to feed it through the firewall with your existing wiring. I have attached the wiring diagram which shows how to wire the dual map feature on the XEDE. Then either dyno tuning or a program fee applies to setup the 2nd map to your requests, like a lower boost map of your existing XEDE Tune. Average cost of this would be $200, but may vary depending on your specific requests. The 2nd map is uploaded using XMap tuning software.

So all up you could be looking at $405.00 or less.

Leah @ CT

Wow thanks Leah I wasn't expecting a response like that. Def thumbs up and thanks for letting me know!