Product Feature: AEM Water/Methanol Injection Kit

AEM 1 Gallon Water/Methanol Injection Kit

http://i567.photobucket.com/albums/s...ps04723811.jpg

Water Methanol Injection is one of the best and least expensive ways to increase the power of your engine. Not only do you make more power, you are able to do so with more of a safety margin due to the lower air inlet temps and decreased chance of detonation that water/methanol allows.

http://i567.photobucket.com/albums/s...psee2ff4e2.jpg

The AEM Water/Methanol Injection kit with 1 gallon tank includes all the elements necessary to do water/methanol injection right on nearly every forced induction vehicle. Imagine having the benefits of a super efficient intercooler and race gas-like detonation control but for hundreds of dollars less and all packaged in a complete kit. Run more boost and ignition timing to gain as much as 20% more horsepower while still using pump gas!

http://i567.photobucket.com/albums/s...psf3f08469.jpg

The AEM Water/Methanol Injection kit comes with more standard high quality features and functionality than any other comparably priced kit on the market. It includes a 1 gallon tank with a built in low level switch, a boost referenced progressive controller, the “Boost Safe” readiness safety system, and a machined billet injector with integral check valve to prevent unintended flow. It also comes with two interchangeable injector nozzles, a recirculation style pump, a LED dash light for system status and low fluid warning, as well as 20 ft. of injection tubing.

http://i567.photobucket.com/albums/s...ps980e3a8a.jpg

Water/methanol injection helps to reduce inlet air charge temperatures and suppress detonation. A highly atomized mist of water/methanol mix is injected into the inlet airstream where it immediately starts to evaporate. The air charge temperature is reduced through evaporative cooling as the fluid changes states and goes from a liquid to a vapor. This “liquid intercooling” effect can reduce intake air temperatures by as much as 100°F or more! A cooler, denser air charge delivers more oxygen that allows for more fuel to be burned and more horsepower to be made. A cooler air charge also helps increase the knock threshold by reducing the chance of pre-ignition and detonation.

http://i567.photobucket.com/albums/s...ps5a953f9f.jpg

Combined, water and methanol can significantly increase your effective anti-knock index allowing for higher boost pressures and more ignition timing advance. Water absorbs heat which allows it to reduce excessive combustion temperatures and slow down the combustion rate. By slowing and controlling the combustion rate the chance of detonation occurring is greatly reduced. Methanol is a cool burning, high anti-knock rated fuel that also helps to cool and control combustion.

http://i567.photobucket.com/albums/s...ps42e521e6.jpg

Water/methanol injection will reduces carbon deposits inside the combustion chamber and in the intake manifold. Many engines use Exhaust Gas Recirculation (EGR) for emissions control which can lead to massive carbon build up inside the air intake. Water/methanol injection will help to eliminate this build up and promote better airflow for better engine efficiency. Reducing carbon build up in the combustion chamber helps to reduce “hot spots” that can cause unwanted pre-ignition and detonation. In some instances, water/methanol injection can also slightly increase fuel economy.

http://i567.photobucket.com/albums/s...ps8fa7a8b0.jpg

The AEM Water/Methanol Injection System uses an on-demand boost referenced progressive controller to drive a high pressure injection pump. Basing injection progressively on manifold pressure allows for the correct amount of water/methanol to be injected at all points along the engine’s power curve. At lower boost levels where only a small amount of water/methanol flow is needed, the controller drives the pump at low speed delivering the necessary flow rate. As boost increases, along with intake air temperatures increasing as well, the controller increases the pump speed allowing for more water/methanol to be injected into the engine, helping to cool and control combustion when it’s needed most.

http://i567.photobucket.com/albums/s...psa370ca64.jpg

The progressive controller has a unique system readiness failsafe called “Boost Safe” that monitors the entire injection system. If at any time the controller detects an error, the “Boost Safe” output will trigger a ground signal. The “Boost Safe” output will activate if there is a short, loss in continuity from a broken wire or bad connection or a high or low voltage condition. The fluid tank comes fitted with a pre-installed low level switch and in the event the fluid level begins to get too low, the “Boost Safe” output will activate notifying you before the system runs completely out of fluid. This failsafe function is an exclusive feature only available on AEM Water/Methanol Injection systems.

http://i567.photobucket.com/albums/s...psa442cdc1.jpg

Now with integral fittings, AEM's recirculation-style pump offers improved performance, reliability and a much smoother, quieter operation when compared to older switched-style pumps. With the use of a new internal bypass design, AEM's upgraded pump eliminates erratic on and off switching/pulsing and ensures consistent fluid delivery for optimum performance. With durability and reliability in mind, AEM has designed the pump with a Santoprene diaphragm and EPDM seals to withstand the harshest of alcohol mixes.

http://i567.photobucket.com/albums/s...ps94c87f26.jpg

This kit is $399.84, but PM me for availability and better pricing on AEM Meth injections kits. These are currently in stock and ready to ship :)

http://i567.photobucket.com/albums/s...psbf111d4f.jpg

GB anyone? Lol

We can definitely work out a group buy for you guys if you want. It would include better shipping rates and cheaper price.

Let me know how many are interested and I'll put it together :)